Simple purge calibration

Test model for measurement right amount of purging volumes with multi-color printing.
52m
4× print file
0.30 mm
0.40 mm
10.00 g
7
39
0
268
updated April 14, 2024

Description

PDF

[English]

I tried various existing purge calibration models, but I couldn't find anything I was satisfied with, so I made a new one.

The type that uses sequential printing without making a wipe tower could not be used because the nozzle clogging often at the time of color change.

The type of making two small layers with a wipe tower was well done, but it was too small to see the color change, and the maximum purge volumes was not enough.

This is a simple model using a wipe tower, so It's hard to get into trouble. It is 50mm3 in 5mm in depth, so if the color changes from 17mm from the front, add 50 (for wipe tower) to 17x10 and it will be 230mm3. If there is no color change from the beginning to the end, the purge volume of 50mm3 is enough.

It takes about 50 minutes to print one 5 colors type with MK3S+/MMU2S. By printing 4 patterns, you can find right purge volumes of all 20 patterns in 5 colors.

color change pattern 1: 1 > 2 > 3 > 4 > 5 > 1

color change pattern 2: 1 > 3 > 5 > 2 > 4 > 1

color change pattern 3: 1 > 4 > 2 > 5 > 3 > 1

color change pattern 4: 1 > 5 > 4 > 3 > 2 > 1

(How to use)

  • Import the STL file into PrusaSlicer, press the ‘Sprit to parts’ button ([P] icon at the top) to split it. (The print settings and purge volume of the 3mf files have been changed. Change only the filament settings and print settings and print.)
  • Change the ‘extrader’ color with reference to the above pattern.
  • Change the ‘Print settings’ of PrusaSlicer from ‘0.20mm QUALITY’ as follows and output it.
    • Layers and perimeters - Layer height - Layer height: 0.3mm
    • Layers and perimeters - Vertical shells - Perimeters: 0
    • Layers and perimeters - Horizontal shells - Solid Layers - Top: 1
    • Layers and perimeters - Horizontal shells - Solid Layers - Bottom: 0
    • Infill - Infill - Top fill pattern: Aligned Rectilinear
    • Infill - Advanced - Fill angle: 0
    • Skirt and brim - Skirt - Loops (minimum): 0
    • Multiple Extruders - Wipe tower - Enable: on
    • Multiple Extruders - Wipe tower - Postion X: 160mm
    • Multiple Extruders - Wipe tower - Position Y: 50mm
      • Place the wipe tower at the bottom right of the model. PrusaSlicer starts printing every layer from near the wipe tower, so the location of the wipe tower is very important.
  • Set all Purging volumes... to 50mm3.

[Japanese]

既存のPurge Calibrationモデルを色々試しましたが、満足できるものがなかったので新しく作りました。

ワイプタワーを作らずにシーケンシャルプリンティングを利用するタイプはカラーチェンジ時にノズル詰まりが多発するので使えませんでした。

ワイプタワーを作って2つの小さな積層を作るタイプはよく出来ていましたが、小さすぎて色の変化を見るのが難しく、また色によっては最大パージ量が足りませんでした。

これはワイプタワーを使ったシンプルなモデルなのでトラブルが起きにくいです。奥行5mm分で50mm3なので、色が変わり切ったところが手前から17mmなら17×10に50(ワイプタワー分)を足して230mm3となります。最初から最後まで色の変化がない場合はパージボリュームは50mm3で十分ということになります。

MK3S+/MMU2Sで5色タイプを1つプリントするのにで約50分。4パターン出力することで5色での組み合わせ20パターン全ての適切なパージ量が決められます。

パターン1: 1 > 2 > 3 > 4 > 5 > 1

パターン2: 1 > 3 > 5 > 2 > 4 > 1

パターン3: 1 > 4 > 2 > 5 > 3 > 1

パターン4: 1 > 5 > 4 > 3 > 2 > 1

(使い方)

  • PrusaSlicerにSTLファイルを読み込んだらSprit to partsボタン(上部の[P])を押して分割してください(3mfファイルはプリント設定やパージ体積は変更済みです。フィラメント設定とプリント設定だけ変更してプリントしてください)。
  • 上記のパターンを参考にエクストルーダー色設定を変更してください。
  • PrusaSlicerのプリント設定を「0.20mm QUALITY」から下記のように変更して出力してください。
    • レイヤーと外周 - 積層ピッチ - 積層ピッチ: 0.3mm
    • レイヤーと外周 - 外壁設定 - 境界線: 0
    • レイヤーと外周 - 水平構造設定 - ソリッドレイヤー - トップ: 1
    • レイヤーと外周 - 水平構造設定 - ソリッドレイヤー - ボトム: 0
    • インフィル - インフィル - トップ塗りつぶしパターン: 整列された直線
    • インフィル - モードIIアドアンスド - 塗りつぶし角: 0
    • スカートとブリム - スカート - ループ数(最小): 0
    • 複数のエクストルーダー - ワイプタワー - 有効: オン
    • 複数のエクストルーダー - ワイプタワー - X位置: 160mm
    • 複数のエクストルーダー - ワイプタワー - Yポジション: 50mm
      • ワイプタワーをモデルの右手前に配置してください。PrusaSlicerはワイプタワーの近くからプリントをスタートするのでワイプタワーの位置はとても重要です。
  • 「パージ体積…」の数値を全て50mm3に設定してください。

Tags



Model origin

The author marked this model as their own original creation.

License