IKEA 365+ Drybox Spoolholder (also for smaller Printers)

IKEA 365+ Drybox Spoolholder for 2 Spool, with space for Silica / Desiccant and a Xiaomi Miija Bluetooth Thermometer.
42
276
8
1561
updated May 26, 2024

Description

PDF

>Version for 1 Spool<

>Version for 3 Spools<

IKEA 365+ 10,6l Drybox Spoolholder for 2 Spool, with space for Silica / Desiccant and a Xiaomi Miija Bluetooth Thermometer. 

Update 2024-04-01

  • Added a splitted in 2 parts version for smaller printers

Update 2024-04-20

  • Added a versions for 25 tube in a complette and splitted version

Update 2024-04-25

  • Added a version which can be printed without bridging and without support →V3.1 for D32 Tubes

Update 2024-04-27

  • added (2x)Federspanner Filament_D60_for_D25 for smaller Spool with lower tension

Update 2024-05-25

  • Added a D32 version without Hygrometer
  • Added splitted version without Hygrometer
  • Added Filamenttensioner with lower tension

 

The main reason I've made this spool holder is….

There are so many Spoolholder which are using bearings at the buttom. But with this kind of rolling system the spool will be pulled from the bearing, espacily if the spool is nerly empty and lightweight. So I've made this solution, where the spool is mounted in the air by a 3D printed spring and a ⌀32 Tube. With this solution, the spool stay in place and rolls very easily. This is also a reason why many Bambu users add weight to their spool regarding this thread:

https://forum.bambulab.com/t/filamentrolle-stellt-sich-auf-im-ams/23638/30

 

Maximum spool width: up to 71mm or less (part is 72mm) I use spools with 65x200

----------------------------------------------------------------------------------------------

I've printed everything out of PETG. 

2 walls, low infill, 3 top and buttom layer

The spring, PETG!!! 

2 walls, no infill, no top and buttom layer 

----------------------------------------------------------------------------------------------

Ikea Container 10,6l

https://www.ikea.com/de/de/p/ikea-365-vorratsbehaelter-mit-deckel-rechteckig-kunststoff-s79276760/

 

For the reverse bowden I used a PTFE tube (OuterD=4 / InnerD3) without coupler.

Simply drill a D4 hole in the Container. They hold very well.

Also i used Endcaps

https://www.printables.com/de/model/827355-4mm-filament-tube-end-cap-for-reverse-bowden

 

Instead of the “(2x)Abrollhalter” I used a PVC tube with 32

There a are very cheap and should be available in every hardware store.

https://www.hornbach.de/p/installationsrohr-starr-m32-grau-3m/5005525/

 

-------------------------------------------German---------------------------------------------

Update 01.04.2024

  • eine geteilte Version für kleinere Drucker hinzugefügt

Update 20.04.24

  • eine Variante für 25 PVC Rohre hinzugefügt in einer kompletten und geteilten Variante

Update 25.04.24

  • eine Variante, die ohne Brücken/Stützstruktur gedruckt werden kann →V3.1 für ⌀32mm

Update 27.04.24

  • Federspanner Filament_D60_for_D25 für kleinere Spuleninnendurchmesser mit geringerer Spannkraft

Update 25.05.2024

  • eine Variante ohne Hygrometer hinzugefügt
  • geteilte Version ohne Hygrometer hinzugefügt
  • Filamentspanner mit weniger Spannkraft hinzugefügt

IKEA 365+ 10,6l Trockenbox Spulenhalter für 2 Spulen mit Platz für Silica / Trockenmittel und ein Xiaomi Miija Bluetooth Thermometer.

Der Hauptgrund, warum ich diesen Spulenhalter gemacht habe, ist....

Es gibt so viele Spulenhalter, die mit Kugellagern an der Unterseite arbeiten. Aber mit dieser Art von Rollensystem wird die Spule aus dem Lager gezogen, vor allem wenn die Spule fast leer und leicht ist. 

Deshalb habe ich diese Lösung gemacht, bei der die Spule durch eine 3D-gedruckte Feder und ein ⌀32-Rohr in der Luft gehalten wird. Mit dieser Lösung bleibt die Spule an ihrem Platz und rollt sehr leicht ab. 

Dies ist auch ein Grund, warum viele Bambu-Benutzer Gewicht auf ihre Spule hinzufügen.

siehe Thread:

https://forum.bambulab.com/t/filamentrolle-stellt-sich-auf-im-ams/23638/30

Maximale Spulenbreite: bis zu 71mm (Breite ist 72mm)

Anstelle des "(2x)Abrollhalter" habe ich ein PVC-Rohr mit ⌀32 verwendet.

Diese sind sehr günstig und sollten in jedem Baumarkt erhältlich sein.

https://www.hornbach.de/p/installationsrohr-starr-m32-grau-3m/5005525/

----------------------------------------------------------------------------------------------

Alles aus PETG gedruckt. 

2 Wände, wenig Infill , 3 top and buttom layer

Die Spulenfeder

2 Wände, kein infill, kein top and buttom layer

 

Für den Reverse Bowden habe ich einen PTFE Schlauch mit Außendurchmesser=4 und Innendurchmesser=3 verwendet ohne Kupplungen.

Einfach ein D4 Loch in den Behälter bohren. Der PTFE Schlauch hält auch ohne Kupplung fest im Behälter.

Zusätzlich habe ich Entkappen verwendet.

https://www.printables.com/de/model/827355-4mm-filament-tube-end-cap-for-reverse-bowden

 

Ikea Behälter 10,6l

https://www.ikea.com/de/de/p/ikea-365-vorratsbehaelter-mit-deckel-rechteckig-kunststoff-s79276760/

 

Tags



Model origin

The author marked this model as their own original creation.

License


Highlighted models from creator

View more