Gridfinity 25 Bin Box For Stuff Version 2.3 6U, 9U and 12U deep options (UNTESTED REMIX)

THIS IS UNTESTED - PRINT AT YOUR OWN RISK (but please provide feedback if you do).

Version 2.4 (2/20/2025) small update to fix incorrect plate descriptions in the 3mf profile.  The current profile is “GRIDFINITY-25BIN-6U_BFS-V2-4-Bambu-v6E-6U-9U-2U.3mf”

Version 2.3 (5/17/2024), includes all improvements from V2.2 as well as the following:

1. Thicker gasket.  Note that the new gasket design means that V2.3 models for the base and lid are not compatible with V2.2 bases or lids.

2. Additional clearance around the bins in the base of the case (thanks to feedback).

Version 2.2 (4/12/2024), includes the following improvements:

1. Redesigned to fit on the bed of a Bambu X1C (256x256), and requires the full bed area. (v2.2)

2. Improved label design with more robust pins. (v2.0)

3. Improved handle design (which should be easier to install) (v2.0)

4. Increased the hole diameter where the M3 SHCS install into the hinges (increase to 5.8mm)  (v2.1)

This is 25 bin version of the 20 bin Gridfinity Box For Stuff.  I've not personally tested this version, however it has been printed by several folks now, and I feel it works OK (but please provide feedback if you see a problem).  This version of 25 bin case is lacking a few updates that have been applied to the 20 bin model, but functionally it is very similar.  You can find more detailed instructions for building the similar 20 bin model, which should also apply to this 25 bin version, at the link below:

https://makerworld.com/en/models/1972161-gridfinity-box-for-stuff-20-bin-ver3-1#profileId-2120575

This 25bin version now includes 6U, 9U and 12U deep bases.

This will require a bed with an area of at least 256x256.

See the 20 bin model for printing and assembly suggestions, since this version is the same, just bigger.  

It requires the following hardware:

(2) M3 x 12mm SHCS  (these hold the latch “cleats” to the top of the case)
(4) M3 x 20mm SHCS 
(4) M3 x 25mm SHCS
(2) M3 x 30mm SHCS
(100) 6x2mm Cylinder Magnets - OPTIONAL (I used 6x3mm, which seem to work OK too)
(SHCS = Socket Head Cap Screws)

The only files that are different from the original design, are the parts for the top and bottom (base) of the case, and the handle.  All latch, and label parts are carried over unchanged from the original (but are included here for convenience).

If using a Bambu X1C/P1P/S printer, this model will require the full bed area, and therefore if using these printers, the “exclusion zone” for the cutter needs to be disabled according to the Bambu Wiki.  Removing the cutter exclusion zone also means that only one color can be printed using that method (no AMS).  If you have problems fitting it on the bed still, it may also be helpful to center the model in the bed (right click > center) and disable a brim.  I was able to slice with the brim set for auto, however it would be best to disable it and work back from there if there is a problem getting it to slice.

AFTER PRINTING WITH THE EXCLUSION ZONE REMOVED (TO USE THE ENTIRE PLATE AREA), PLEASE BE SURE TO CHECK THAT THE EXCLUSION ZONE (0x0, 18x0, 18x28, 0x28) IS RESTORED IN THE PRINTER SETTINGS FOR SUBSEQUENT PRINTS.  

REMOVING THE EXCLUSION ZONE MAY PERSIST AFTER PRINTING A PROFILE, AND CAUSE PROBLEMS WITH INTERFERENCE ON SUBSEQUENT PRINTS!

I have included a 3MF file as a convenience, however it is NOT TESTED, so USE THE PROFILE AT YOUR OWN RISK.  

SLICING THIS MODEL REQUIRES DISABLING THE CUTTER EXCLUSION ZONE TO USE THE FULL BED AREA ON A BAMBU X1C/P1P/P1S.  MAKE SURE YOU FULLY UNDERSTAND THE HARDWARE AND SCLICER REQUIREMENTS FOR DOING THAT, BEFORE PRINTING THIS MODEL.  

There is a 3MF file from Bambu Studio included, based on an X1C profile (with 0.4mm nozzle).  The profile has all parts including a plain (no logo) top.  The 3MF file will not slice, until the cutter exclusion zone has been disabled (this is intentional).  

If you print this, please know that although I am 99% confident that the model is going to be OK, it is still untested.  So if you run into a problem with it, please let me know and I will see what I can do to fix it.  If the problem relates to fit however, please be sure to run a flow calibration, since there are some parts which are designed for a close fit.  If you print this and provide me feedback (or post a make with feedback), I may use that information to update this description, so I can get rid of all the untested language, and just let it ride as a normal tested model similar to what I would normally post.

Something else to note about this design, it is older without the modular latches, so please take care when latching it for the first time.  With this older design, there were some reports on similar cases of the lower latch mount cracking due to problems with clasps that were too tight (and very difficult to close).  If you find the latches seem to require excessive force to close, stop, and post a comment to let me know. I will try to assist. The fix, if that happens, is a longer U shaped latch clasp, which I can provide if I know there is a problem.  Eventually I may update this 25 bin case to the modular latches, however it is not a priority right now.

Other stuff:

There are similar multi compartment latching lid bins available at the links below:

Gridfinity 1x1 Bins with Latching Lids v1.0

Gridfinity 1x2 Bins with Latching Lids v1.0

Gridfinity 1x3 Bins with Latching Lids v1.0

Gridfinity 1x4 Bins with Latching Lids v1.0

Gridfinity 2x2 Bins with Latching Lids v1.0

Gridfinity 2x3 Bins with Latching Lids v1.0

If you need some bins for small parts, the following bins with covers are a good option to use with the Box For Stuff 20 bin and 25 bin cases (or other 6U tall cases):

1. 1x1, 1x2 (3 Compartment) and 1x4 (6Compartment) bins with lids (3U, 6U and 9U) - version 2.1 (older non-latching type)

2. 1x2, 1x3 and 1x4 single compartment bins with tabbed lids (3U, 6U and 9U) - version 2.1 (older non-latching type)

3. 1 compartment 2x1 (6U) bin with a magnet pickup tool

4. 1x2, 1x3, 1x4 (6U, 9U and 12U) Lidded Bin for Stuff with Latch Version 2.0

5. 2x2, 2x3, 2x4 (6U, 9U  and 12U) Lidded Bin for Stuff with Latch Version 2.0

6. 3x3, 3x4 (6U, 9U  and 12U) Lidded Bin for Stuff with Latch Version 2.0

7. 4x4, 4x5 (6U, 9U  and 12U) Lidded Bin for Stuff with Latch Version 2.0

If you want to check out my other Gridfinity cases, you can find them at the links below:

1. Gridfinity Box For Stuff 20 bin (6U) (updated to v2.3)

2. Gridfinity Box For Stuff 25 bin (6U) (max size for a Bambu X1C/P1S)

3. Gridfinity Box For Stuff 16 bin (6U) (Ender 3 size)

4. Gridfinity Box For Stuff 16 bin - 12U deep version (Ender 3 size)

5. Gridfinity Box For Stuff 2 bin (6U) mini version (can be used to test)

6. Gridfinity Single Watch Case 

7. Gridfinity Triple Watch Case 

Additionally, there are some alternate latch parts which may help if you do not have the M3x30mm screws or have difficulty installing the latch “cleat”.

If you want to store some small hardware and need some good labeled bins, Ch3vr0n posted some segmented bins for the Gridfinity system here:

https://www.printables.com/model/732655-gridfinity-boxes-for-gridfinity-box-for-stuff-20-b

If you find these models useful, please post a like or a comment with some pics of your prints. 

You can find the other things I'm working on at my blog here.  You can also follow me here on Printables to see what new stuff I post.  If you would like to support my work, you can Buy Me A Coffee using this link:

https://www.buymeacoffee.com/mystoopidstuff

Thanks for looking!

Thanks and Acknowledgements: 

The models here could not have been made without the work of Zach Freedman, who introduced the world to Gridfinity, and then set it free for everyone to use.  These models are not based on direct remixing of Zach' original models, but they are fully compatible, and use the same, or a similar specification for the bin bases, bin lips and base grids, which Zach Freedman developed.   Zach Freedman's work is available on Thangs, and you can find examples of his Gridfinity designs here and here, which are available under his MIT license.  If you like this model, or want to learn more about Gridfinity, you can check out Zach Freedman's YouTube, or you can support Zach Freedman's work on Patreon (patreon.com/zackfreedman).

Changelog:

Update 4/13/2024 - The files were corrected and updated to v2.2, since the prior 2.1 files did not fit the Bambu X1C/P1P bed.  The current version files will fit the Bambu X1C, however the cutter exclusion zone needs to be disabled for it to fit (see notes below).

Update 4/26/2024 - There is now a 9U and 12U deep version of the base (along with the original 6U version).  As with the rest of the models here, they are untested, but a 3MF Bambu Studio profile for an X1C with 0.4mm nozzle is included to get things started.

Update 5/17/2024 - Updated this to v2.3.

This version hold 25 1x1x6U Gridfinity bins.