Mooody Pumpkin

Hi there, my name is Mooody Pumpkin. I am your mood indicator for every day. If you expect a happy day, set my face to a happy face. If you expect a day with problems, set my face to a sad face.

It is very easy to change my mood, as my Mooody internal gears let me turn the other part of my mouth when you turn one part.

This is an easy print. No supports are required. Please note the detailed assembly instructions. Some glue is needed for my assembly.

2022-11-06 Added second type of mouth

To make your Mooody Pumpkin look a bit more scary I have added a mouth type 2 with the STLs MP mouth left type 2 V1.stl and MP mouth right type 2 V1.stl.

Enjoy printing Mooody Pumpkin.

Print Settings

Printer:

FLSUN Super Racer

Rafts:

No

Supports:

No

Resolution:

0.2 mm initial layer, 0.2 mm layer height

Infill:

15 %

Filament: GIANTARM, Verbatim PLA

Orange, green, black

Notes:

Nozzle not larger than 0.4 mm to be able to print the fine details of the gears and the stem.

You can print the two parts of the pumpkin and the gears in orange color. Print the stem in green and the two parts of the mouth in black or any other contrasting color.

Post-Printing

Mooody Pumpkin assembly part 1

Print all the parts of Mooody: the pumpkin back, the pumpkin front, the two gears, the steam and the two parts of the mouth.

Mooody Pumpkin assembly part 2

Look at the gears. My printer has created a small blob at the top of one gear. Remove any blob with a sharp knife.

Mooody Pumpkin assembly part 3

Put the back part of the pumpkin in front of you.

Mooody Pumpkin assembly part 4

Add the gears EXACTLY as shown in the picture. Please note that the left gear has a small indent to identify it.

Mooody Pumpkin assembly part 5

Prepare the top part of the pumpkin shown on the picture at the right hand side. The large holes are the eyes and they must be on top. The small holes are for the shaft of the gears. Test fit the top part to the bottom part.

Mooody Pumpkin assembly part 6

Test fit the two parts of the mouth. If you have problems to get a mouth part into the inset of the gear, look for a blob and remove is with a sharp knife.

Turn one part of the mouth to check Mooodies functionality. If the two parts do not perfectly fit, try to exchange them.

Mooody Pumpkin assembly part 7

Sad Mooody should look as shown in the picture.

Mooody Pumpkin assembly part 8

Remove the two parts of the mouth and set them aside with each on the correct side.

Mooody Pumpkin assembly part 9

Remove the top part of the pumpkin without turning the gears. Put some glue on the back part. Do not use too much glue in the area of the gears to prevent them from getting stuck.

Mooody Pumpkin assembly part 10

Put the top part of the pumpkin to the bottom part to glue both parts together. Let the glue dry.

Mooody Pumpkin assembly part 11

Glue the right part of the mouth into position. Do not use too much glue to prevent the gears from getting stuck.

Mooody Pumpkin assembly part 12

Glue the left part of the mouth into position. Do not use too much glue to prevent the gears from getting stuck. Let the mouth dry.

Mooody Pumpkin assembly part 13

Glue the stem to the inset at the back as shown in the picture.

Mooody Pumpkin assembly part 14

If you would like to hang Mooody at a wall, you can use a string. There are two holes to put a string through. The string can go behind the stem, as there is a gap. Hang Mooody Pumpkin at a wall.

The assembly is now complete. I hope you will set the happy face most of the days.

Enjoy printing Mooody Pumpkin.

Second type of mouth

This is Mooody Pumpkin with the more scary looking mouth.