Build and play
Print instructions
|
Build for fun!
|
|
All the parts has been redesigned a bit.
The holes is now cc 10mm. This means that you can position the cubes more flexible. |
The old system if not compatible in this matter. However for the cubes there are transition cubes which will fit the old and the new.
I have noticed that wheels is a big deal.
Therefor I've decided to build a raceway for the vehicles.
I am also making a 60% raceway to fit common small cars.
File
Comment
Cube.stl
A cube without any link
CubeCenterPin.stl
A cube with one center pin
CubeCornerPins.stl
A cube with 4-corner pins
CubeMidPins.stl
A cube with 4-middle pins
CubeHalf.stl
A cube, cut diagonal
CubeTransition.stl
A transition cube without any link, from the old system
CubeTransitionCenterPin.stl
A transition cube with one center pin, from the old system
CubeTransitionCornerPins.stl
A transition cube with 4-corner pins, from the old system
CubeTransitionMidPins.stl
A cube with 4-middle pins, from the old system
Link.stl
Short link
LinkMedium.stl
Medium sized link
LinkMediumB.stl
Medium sized link, both ends
LinkMediumBLid.stl
A "lid" for Link Medium B
LinkLong.stl
Long link
LinkLongB.stl
Long link, both ends
LinkLongBLid.stl
A "lid" for Link Long B
M4_5 Bolt 14mm.stl
Bolt 4.5mm, in sizes 14,24,34,44,54,64,74,84 mm
M4_5 Nut Scale to 107.8.stl
Nut to 4.5mm bolt, scale to 107.8% in slicer
M8 Bolt 15mm.stl
Bolt 8mm, in sizes 15,25,35,45,55,65,75,85 mm
M8 Nut Scale to 106.stl
Nut to 8mm bolt, scale to 106% in slicer
Stick2.stl
Stick, comes in 2,3,4,5,6,7,8 sections
TowBlockWithLink.stl
Tow block with link
TowBlock.stl
Tow block
TowLink.stl
Tow link for two TowBlocks
BlockLink.stl
A link to connect any cube etc...
WheelBig50mm.stl
Wheel for 8mm bolt or pin, suggested use with 30mm wheel
WheelBig40mm.stl
Wheel for 8mm bolt or pin, suggested use with 20mm wheel
WheelBigPin.stl
Pin to big wheels *2)
WheelSmallPin.stl
Pin to small wheels *2)
WheelBalloon40.stl
A sphere with holes, BALLOON Wheel
WheelBalloon50.stl
A sphere with holes, BALLOON Wheel
Kryss.stl
A cross, for e.g. a Helicopter
Fast nyckel 13mm v1.stl
A tool for the bolts and nuts of course :-) *1)
Notes
*1) For 7.5mm key (the M4.5), scale it to 57.7% in the slicer, that is for X, Y and Z
*2) Can be very tight, but when on the wheel the wheel should spin free
Compatible with
https://www.prusaprinters.org/prints/40925-raspberry-pi-case-for-camera-with-flexible-stand
More Notes
I have experienced that different filaments have different properties. Sometimes the pins fits
the holes, sometimes too tight and sometimes to loose. You have to try yourself. if it wont fit
in one way it may fit in another. You may have to "exercise" the parts.
Anyway, Have fun!
Compatible raceway.
Raceway one meter in diameter (24 pieces to print), with options such as driveway and hills 10% or 15%
