Tronxy X5SA Riemenspanner Belt Tensionier

Dies ist ein Riemenspanner für den Tronxy x5sa
1
21
0
440
updated April 9, 2023

Description

PDF

Deutsch

Dies ist ein Riemenspanner für den Tronxy X5SA. Ich habe ihn in PLA gedruckt. Die Festigkeit ist vollkommen ausreichend.

Um diesen Riemenspanner vollständig zu montieren, benötigt ihr folgendes Zubehör.

Einen Stift und eine Lineal
4x Linsenkopfschraube mit Kunststoffgewinde Länge 20 mm
2x M5 Schraube Länge 40mm
2x M5 Mutter
Einen 4er Inbus Schlüssel sowie das Zubehör Werkzeug des Druckers.

Schritt 1
Ausdrucken von
1x Grundplatte
1x Deckel
2x Spannklotz

Schritt 2
Steckt die Muttern in die Öffnungen in der Mitte der Grundplatte achtet darauf das Gewinde mittig zum Loch auszurichten. Lasst die M5 Schrauben noch weg.

Schritt 3
Drehen Sie zuerst die Schrauben vom HotEnd / Halteplatte um und montiert gleichzeitig die Grundplatte mit den Schrauben nach dem montieren muss zuerst das Spiel aus den Führungsrollen wieder entfernt werden.

Schritt 4
Spannt die beiden Riemen einmal von Hand bis zur inneren Kante der Spannklötze in ihrer Anfangsposition (Außenkannte der Führungen) und markiert diesen Punkt am Riemen mit einem Stift.

Schritt 5
Steckt die Riemen wie auf dem Bild zu sehen ist durch den Spannklotz und fixiert ihn zur Sicherheit mit 2 cm Filament oder etwas ähnlichem. Schraubt jetzt die Schrauben durch die Spannklötze in die Muttern so das die Riemen nur leicht gespannt sind.

Schritt 6
Jetzt den Deckel montieren und festschrauben.

Abschluss
Spannt nun sterben Riemen gleichmäßig, so dass das Euer Drucker Sich Nicht Verzieht Hierzu Können Sie Ein Lineal Verwenden Um Die Abstände Zwischen Gehäuse Und Hotend Profil / Gantry Zu Messen.

English

This is a belt tensioner for the Tronxy x5sa I have printed it in PLA the strength is completely sufficient.

To assemble this belt tensioner completely you need the following accessories.

A pencil and a ruler
4x pan-head screw with plastic thread length 20 mm
2x M5 screw lentgh 40 mm
2x M5 nut
A 4mm Allen key and the printer's accessory tool.

Step 1
Print out
1x base plate
1x cover
2x clamping block

Step 2
Insert the nuts into the holes in the centre of the base plate, making sure the thread is centred on the hole. Leave out the M5 screws.

Step 3
First turn over the screws of the HotEnd / holding plate and at the same time mount the base plate with the screws. After mounting, first remove the play from the guide rollers.

Step 4
Tension the two frames once by hand up to the inner edge of the tensioning blocks in their initial position (outer edge of the guides) and mark this point on the frame with a pin.

Step 5
Put the straps through the tensioning block as shown in the picture and fix it with 2 cm of filament or something similar to be on the safe side. Now screw the bolts through the tensioning blocks into the nuts so that the frames are only slightly tensioned.

Step 6
Now mount the lid and screw it tight.

Finish
Tension the belts evenly so that your printer does not warp. You can use a ruler to measure the distance between the housing and the hotend profile.

How I Designed This

 

Fusion 360

Viel Spaß – Have Fun

 

Tags



Model origin

The author marked this model as their own original creation.

License