10.07.2023 - Issue with the mounting location of the AMS filament buffer:
10.07.2023 - Issue with support structure in the screw holes and print quality:
06.05.2023 - Problem with AMS Power connector:
02.05.2023 - thin layer spool holder problem:
01.04.2023 - spool holder screw problem:
About the model:
Due to its size, the back panel is divided into 4 parts. These are connected using the “Connector”- components (8x) that are pressed into the back panel plates. No additional screws are required for assembly.
I printed it in a way that the mounting points for the "Connector" components are on the top, resulting in a nice surface for the outside thanks to the structure of the print bed.
In the print files, you will find the Backpanel_Part1-4 (.stp) files, as well as the Connector (.stl) and the Backpanel_whole_part (.stp) as a complete piece, in case you want to split it yourself or print it as a whole. You can also use the STEP files for remixing.
The Backpanel_Part4 is available with and without extra mounting holes for a silencer since the chamber fan can be very loud. The silencer is a remix of the Bambu X1 Exhaust Muffler by ourangrybadger. Thank you for sharing your STEP file for remixing!
Additionally, you will find the Backpanel_template (.3mf) file there. In this file, I have included what I believe to be the optimal print settings.
Support: Yes - normal
Layer height: 0.2mm
Infill: 50% cubic
Bed temp: 45°C to avoid warping
Printed with PLA.
Description:
For the BambuLab P1P, it is possible to install the original chamber fan from the BambuLab X1C.
Here's the link to the fan: Chamber Temperature Regulator Fan | Bambu Lab EU The fan can be connected to the original P1P board (Port Fan1), as it has the same board as the X1C.
The fan is especially useful for enclosed printers to dissipate heat. Without it, extruder clogs can occur with filaments that don't require a warm environment.
To mount the fan, I used the fan holder from suit.
But now comes the problem: the P1P does not have holes in the back panel to exhaust the air from the fan. There are several options:
I wanted to take full advantage of the X1C without destroying the original back panel (especially for warranty reasons). That's why I traced the original back panel 1-to-1 and made it slightly thicker so that it could be printed.
I added a step-file of the whole part if you want to remix it.
Zum Modell:
Aufgrund der Größe ist die Rückwand in 4 Teile aufgeteilt.
Verbunden werden diese über die “Connector” Bauteile (8x) die in die Rückwandplatten eingepresst werden. Für die Montage sind also keine weiteren Schrauben notwendig.
Gedruckt habe ich so, dass die Montagestellen für die “Connector”-Bauteile oben liegen. So ergibt sich durch das Druckbett eine schöne Oberfläche für die Außenseite.
In den Druckdateien findet ihr neben den Backpanel_Part1-4 (.stp) auch die Connector (.stl) und das Backpanel_whole_part (.stp) als ganzes Teil, falls ihr es selber teilen wollt oder im ganzen Drucken könnt. Die Step Dateien könnt ihr auch zum remixen verwenden.
Das Modell Backpanel_Part4 gibt es einmal ohne und einmal mit extra Montagelöchern für einen Schalldämpfer, da der Chamber-Lüfter sehr laut werden kann.
Der Schalldämpfer ist ein Remix vom Bambu X1 Exhaust Muffler von ourangrybadger.
Vielen Dank, dass du deine Step-Datei zum remixen freigegeben hast!
Außerdem findet ihr dort die Datei Backpanel_template (.3mf). In dieser Datei habe ich die, meiner Meinung nach optimalen, Druckeinstellungen hinterlegt.
Support: Ja - normal
Layerhöhe: 0.2mm
Infill: 50% kubisch
Betttemperatur: 45°C um Warping zu vermeiden
Gedruckt mit PLA.
Beschreibung:
Für den BambuLab P1P gibt es die Möglichkeit, den originalen Chamber Fan (Raumlüfter) des BambuLab X1C zu installieren.
Hier der Link zum Lüfter: Chamber Temperature Regulator Fan | Bambu Lab EU
Der Lüfter kann an die originale Platine des P1P angeschlossen werden (Port Fan1), da dieser dieselbe Platine wie der X1C besitzt.
Der Lüfter ist vor allem für geschlossene Drucker interessant um die Wärme abzuführen. Bei Filamente die keine warme Umgebung brauchen, kann es sonst zu Verstopfungen des Extruders führen.
Zum montieren des Lüfters, habe ich den Lüfterhalter von suit genutzt.
Jetzt kommt aber das Problem: der P1P hat keine Löcher in der Rückwand um die Luft des Lüfters abzuführen. Hier gibt es jetzt mehrere Möglichkeiten:
Ich wollte die vollen Vorteile des X1C nutzen ohne dabei die originale Rückwand zu zerstören (Vor allem aus Garantiegründen). Deshalb habe ich die originale Rückwand 1 zu 1 nachgezeichnet und etwas dicker gemacht damit diese druckbar ist.
Ich habe eine Step-Datei des Modells mit hochgeladen falls jemand das Modell remixen möchte.
The author marked this model as their own original creation.