PRUSA I3 MK3S+ Hotend Orginal PlastParts Redigeret til MMU2S - MMU3

UK:

Hotend two MMU2S - MMU3
Complete Hotend for MMU2S - MMU3 has redesigned it quite a bit, and I use "AYF MK3s Part fan duct v3.stl" the new cooler for the Hotend which provides perfect cooling and visibility...

https://www.printables.com/model/255518-ayf-mk3s-part-fan-duct/files?fbclid=IwAR2MBHNeaU7XjmGvueadnEhcDvWqUClhjN6M9Va4ztaAoOiK3FrcgZgV3q0

The Hotend has been redesigned from the original parts for the Hotend from Prusa Research.

https://www.facebook.com/100000655244863/videos/pcb.3951717378387423/1965191720356571

Hotend MMU2S - MMU3 Plast Parts can be downloaded here on this page.

Information about 3D Print:
Filament: Devil Design PETG
Hotend: 235
Bed: 85
Layer: 0.20mm Quality @MK3

Tube PFTE Tools:
Using my new tool for tube pipes, it is important that the Filament wire can slide through unobstructed all the way, so both inside and outside the tool is 60 degrees and cuts it off in 42.3mm.
If the thread has to go through, remember to use the inner one so that it does not stop at the edge as the MMU2S - MMU3 cuts the filament straight across...
And just take the outer edge of the ones that go down into the print so they can go to the bottom...

Cutting tool so that the tube becomes 42.3 mm

Outside 60° Degrees

Inside 60° Degrees

Materials:
Knives from Hobbykniv,
Pinole drill
Fits Original Hotend for Prusa I3 MK3S+

Information about 3D Print:
Filament: Devil Design PETG
Hotend: 235
Bed: 85
Layer: 0.20mm Quality @MK3

STL Link:
https://www.facebook.com/.../permalink/3932034627022365

Can also be downloaded here on the model database:
https://www.printables.com/model/250612-tube-pfte-tools

Regards

Leif Lumby Henriksen Odense3D Facebook "https://www.facebook.com/groups/2911561982402973"

DK:

Hotend to MMU2S - MMU3
Komplet Hotend til MMU2S - MMU3 har tegnet en del om på den, og jeg bruger ”AYF MK3s Part fan duct v3.stl” den nye køler til Hotend som giver perfekt køling og udsyn...

https://www.printables.com/model/255518-ayf-mk3s-part-fan-duct/files?fbclid=IwAR2MBHNeaU7XjmGvueadnEhcDvWqUClhjN6M9Va4ztaAoOiK3FrcgZgV3q0

Hotend er tegnet om ud fra de originale dele til Hotend fra Prusa Research.

https://www.facebook.com/100000655244863/videos/pcb.3951717378387423/1965191720356571

Hotend MMU2S - MMU3 Plast Parts kan hentes her på siden.

Oplysninger om 3D Print:
Filament: Devil Design PETG
Hotend: 235
Bed: 85
Layer: 0.20mm Quality @MK3

Tube PFTE Tools:
Bruge mit nye værktøj til tuberør, det er vigtigt at Filament tråden kan glide uhindret igennem hele vejen, så både indvendigt og udvendigt 60 graderes værktøj samt klipper det af i 42,3mm.
Skal tråden gå igennem så husk bruge den indvendige så den ikke stopper på kanten da MMU2S - MMU3 skære filament lige over...
Og tag lige den udvendige kant på dem der går ned i print så de kan gå i bund…

Klippeværktøj så tube rør bliver 42,3 mm

Udvendig 60° Grader

Indvendig 60° Grader

Materialer:
Knive fra Hobbykniv,
Pinolbor
Passer til Original Hotend for Prusa I3 MK3S+

Oplysninger om 3D Print:
Filament: Devil Design PETG
Hotend: 235
Bed: 85
Layer: 0.20mm Quality @MK3

STL Link:
https://www.facebook.com/.../permalink/3932034627022365

Kan også hentes her på modeldatabase:
https://www.printables.com/model/250612-tube-pfte-tools

Hilsen

Leif Lumby Henriksen Odense3D Facebook “https://www.facebook.com/groups/2911561982402973”

Hotend two MMU2S - MMU3
Complete Hotend for MMU2S - MMU3 has redesigned it quite a bit, and I use "AYF MK3s Part fan duct v3.stl" the new cooler for the Hotend which provides perfect cooling and visibility...

https://www.printables.com/model/255518-ayf-mk3s-part-fan-duct/files?fbclid=IwAR2MBHNeaU7XjmGvueadnEhcDvWqUClhjN6M9Va4ztaAoOiK3FrcgZgV3q0

The Hotend has been redesigned from the original parts for the Hotend from Prusa Research.