LED Wandleuchte Inspiriert durch Nanoleaf Lines

WLED Wandleuchte Inspiriert durch Nanoleaf Lines, die mit einem ESP32 gesteuert werden kann
154
283
0
4196
aktualisiert 11. April 2022

Beschreibung

PDF

Die LED Wandleuchte wurde während eines Twitch Streams entworfen, modelliert, programiert und am Ende auch zusammengebaut. 

Anleitung Lampe:

Als erstes werden alle benötigen Komponenten wie in der Druckliste angegeben gefertigt. Während dessen kann schon vieles zugeschnitten werden.

  • Die LED-Streifen werden in ca. 30cm lange Stücke an der jeweils vorgesehen Stelle geschnitten.
  • Bei den Aluminium-Profilen werden 32cm lange Teile benötigt.
  • Die Kabel  an den Steckverbindern können auch schon auf die Länge von ca. 6cm gekürzt und 5-6mm abisoliert werden.
  • Zu guter letzt wird der Schrumpfschlauch noch auf ca. 12mm zugeschnitten.

Jetzt können jeweils zwei Abschnitte vom Schrumpfschlauch auf jeden LED-Streifen geschoben werden. Danach können die Kabel der Steckverbinder an den jeweiligen Streifen gelötet werden (Buchse und Stecker bei jedem Streifen ans gleiche Ende löten). Hierbei ist immer auf die Laufrichtung der LED-Bänder zu achten. Nun kann der Schrumpfschlauch über die Lötstellen gezogen und geschrumpft werden.

Die Leuchtelemente werden jetzt zusammengebaut in dem die Profilklammen in die Enden der Aluminiumprofile geschoben werden und der LED-Streifen mittig auf die Innenseite der Profile geklebt werden.

Jetzt können die Knotenpunkte mit M4 Gewindeeinsätzen versehen werden, diese werden mittig in die Röhre eingeschmolzen. Auf der Rückseite der Knotenpunkte bringt man jetzt zur Vorbereitung schon mal das Montageklebeband auf. 

Die Leuchtelemente können jetzt in der Gewünschten Form mit hilfe der Knotenpunkte zusammengesteckt werden. Es kann leider nicht jede Form erzeugt werdenauf, da auf die Laufrichtung der LED-Bänder Rücksicht genommen werden muss. 

Wenn alle Elemente an der richtigen Position sind können Sie mithilfe der Deckel und der passenden Schraube am Knotenpunkt fixiert werden.

Nun kann der Schutzfilm vom Montageklebeband entfernt werden und die Lampe am besten mit der Unterstützung einer weiteren Person an die Wand geklebt werden.

(die Anleitung kann auf den Projektbildern nachvollzogen werden)

Anleitung Steuerung:

Man kann die LEDs auf verschiedene Art und Weisen steuern. Bei der Verwendung von WS2812 Streifen gibt es zum einen fertige “WS2812-Controller” man kann sich aber auch eine Steuerung mit Hilfe eines Mikrocontroller (beispielsweise einem ESP 32) selber bauen.

Bei der Verwendung eines Mikrocontroller kann ich die Software vom WLED-Projekt empfehlen. Sie ist einfach aufzuspielen und kann dann übers Netzwerk gesteuert werden. Zudem findet man dort auch eine Anleitung zur Verbindung mit den Streifen und eine Information zu kompatibler Hardware.

 

Druckdaten:

  • Schichthöhe: 0,2mm
  • Infill: 15%
  • Schichten oben und unten: 3
  • Wandlinien: 3
  • Stützstruktur: größtenteils keine / teilweise konzentrisch

Benötigte Materialien:

  • PLA
  • 3x SO-TECH LED Profil-33, jeweils 2 Meter (also insgesamt 6 Meter)
  • WS2812, 60Pixels/m (ca. 6 Meter)
  • 17x JST SM 3PIN Stecker und Buchse (mit 10 - 15 cm Kabel)
  • 40 cm - 45 cm Schrumpfschlauch, Durchmesser 7.0/3.5
  • ESP 32 Microcontroller 
  • Netzteil 5V 10A
  • Netzkabel
  • Montageklebeband
  • 11 - 14x Gewindeeinsatz M4 x 8,1mm (Schmelzgewinde)
  • 11 - 14x Senkkopf Schraube M4 x 10mm

Druckliste:

  • 36x Profilklammer.stl
  • 11 - 14x Knotenpunkt.stl (je nach Anordnung)
  • 11 - 14x Deckel.stl (je nach Anordnung)

 


 →ENGLISH VERSION ←

The LED wall light was designed, modeled, programmed and finally assembled during a twitch stream.

Instruction Lamp:

First of all you have to print the required components as specified in the print list. A lot of work can be done during the print time.

  • cut the LED strips into approx. 30cm long pieces at the intended location
  • the aluminum profiles need to be 32cm in length
  • the cables that came out of the connectors can also be shortened to a length of approx. 6cm and stripped of 5-6mm
  • last but not least, the shrink tubing is cut to about 12mm

Two sections of shrink tubing can be pushed onto each LED strip. Then the cables of the connectors can be soldered to the respective strips (socket and plug solder to the same end for each strip). It is always important to pay attention to the running direction of the LED strips. Now the shrink tubing can be pulled over the soldering points and shrunk.

Next: the lighting elements can be assembled by pushing the profile clamps into the ends of the aluminum profiles. Then remove the adhesive protection film of the LED strips and glue it  centrally to the inside of the profiles.

Now the nodes can be provided with M4 threaded inserts, which are melted into the center of the tube. The mounting tape can be applied to the back of the nodes in preparation.

The light elements can now be put together in the desired shape using the nodes. Unfortunately, not every shape can be created, as the running direction of the LED strips must be taken into account.

When all elements are in the correct position, they can be fixed to the node using the cover and the appropriate screw.

Now the adhesive protection film can be removed from the mounting tape. The lamp can be attached to the wall, preferably with the help of another person.

(The instructions can be traced on the project images)

Instruction Controler:

You can control the LEDs in different ways. When using WS2812 strips, there are ready-made “WS2812 controllers” but you can also build a controller yourself using a microcontroller (e.g. an ESP 32).

When using a microcontroller I can recommend the software from the WLED project. It is easy to install and can then be controlled via the network. You will also find instructions for connecting to the strips and information on compatible hardware there.

Print data:

  • layer height: 0,2mm
  • infill: 15%
  • top and bottom layers: 3
  • wall layers: 3
  • support structure : mostly none / partly concentric

Required materials:

  • PLA
  • 3x SO-TECH LED Profile-33, 2 meters each (total of 6 meters)
  • WS2812, 60Pixels/m (about 6 meters)
  • 17x JST SM 3PIN plug and socket (with 10 - 15 cm cable)
  • 40 cm - 45 cm Shrink tubing, diameter 7.0/3.5
  • ESP 32 Microcontroller 
  • Power supply 5V 10A
  • power cord
  • mounting tape
  • 11 - 14x threaded insert M4 x 8,1mm
  • 11 - 14x Countersunk head screw M4 x 10mm

Print list:

  • 36x Profilklammer.stl
  • 11 - 14x Knotenpunkt.stl (depending on the arrangement)
  • 11 - 14x Deckel.stl (depending on the arrangement)


 

Tags



Herkunft des Modells

Der Autor hat die Herkunft des Modells noch nicht angegeben.

Lizenz