G9 Holster

See Zip file for all files including STL & STEP.

---Citations:
This is a ripoff of the Recover Tactical G7 OWB Holster.

---Description:
This is a minimalist holster system that can be used on almost anything with a picatinny rail on the front.
The Rail slides into the Fork. The retention tension is adjustable via a bolt.The Fork is mounted to a Paddle, the Paddle is mounted to a ____ (pants, wall mount, car mount...)

---Updates:
V1.1:
Made some changes to the Fork: Added a V1.2 that is a single piece and requires less support. add different variants to the original Fork, 0deg, 4deg & 8deg. This represents the inward angle of the forks when assembled, the default was 8deg.
Added an image of the new Fork design.

---Variants:
Rail: The part that mounts to the tool.
Fork: The retaining piece that connects the tool to the paddle.
Paddle: The adapting system for the Fork, for use with the included as well as many existing holster systems.
 Circle: Used with mounting systems that are a circle surrounded by ridges for adjusting the angle, may also be compatible    with a SERPA QD systems.
 Triangle: Can be mounted to a SERPA QD system if you use one of those or the included belt options.
Belt Loop: A simple belt mounting option, fits up to 2" belts.
Belt Drop: Another belt mounting option but it offsets the holster down 60mm from the center of the belt, fits up to 2" belts.
Belt Slide: A slip on mounting oprion if you prefer not to take your belt off.

---Hardware:
Rail:
M4x12mm bolt & nut
M3x5mm bolt & nut
Fork:
2xM4x12mm bolt & nut
2xM3x10mm Bolt
Paddle:
3xM4x10mm bolt & nut
 Belt Loop: 3xM4x12mm bolt & nut
 Belt Drop: 3xM4x12mm bolt & nut
 Belt Slide: 2xM4x16mm bolt & nut
Circle:
1/4-28x1/2" bolt & nut
Further hardware will be required to mount Paddles to a seperate holster system.

---Printed Parts:
Rail:
 L_R: regular is as close to the original as I could get it; Ext has a slightly larger gap on the pic rail making it   slightly more compatible with other accessories; Ext-TX22 is an Ext with that is custom fit to a Taurus TX22.
 2xPeg, print 2 of these
 PicStop (Narrow is for if the normal is too wide for your rail)
Fork: consists of 2x tongs, 2x tabs, and a c-clip; all parts can be found in the Fork file.
Paddle: Print your Paddle of choice depending on what holster sytem you use.
 Belt Loop: Use in combination with the Paddle Triangle for attaching to a belt.
 Belt Offset: Use in combination with the Paddle Triangle for attaching to a belt.
 Belt Slide: Use in combination with either the Paddle Triangle or Paddle Circle depending on which Paddle you prefer.

---Print Settings:
Plenty of walls and infill.
Supports will be needed.
I have provided orientation recommendation images.

---Assembly:
Rail:
The 2xPegs go into one of the L_R halves, you can glue them in if you want. 
The PicStop goes into one of the grooves on the top of the L_R's to keep the assembly from sliding off the tool, glue is optional.
The L_R's sandwhich onto the rail of a tool, help together by the M3 & M4 bolts.
Fork:
The 2xM3x10mm bolts are used to hold the small tabs to the larger tongs. 
The 2xM4x12mm bolts are used to connect the two tongs together. Note that the more inward bolt can be used to tighen the holster.
The c-clip is slid over the end of the tongs once they are screwed together.
Paddle:
Use the 3xM4x10mm to mount the Fork to the Paddle of choice.
 Belt Loop: Use the 3xM4x12mm to mount the Paddle to the Belt Loop. Use a heat gun to bend the ends if you want.
 Belt Drop: Use the 3xM4x12mm to mount the Paddle to the Belt Drop.
 Belt Slide: Use the 2xM4x16mm to assemble the Belt Slide Top and Base. Can also be shaped with a heat gun.