3D Models 3D PrintersAccessories

New Mounting Cover for Rosahl M-3M1R Dehumidifier Membrane based Filament Drybox or Bambu Lab AMS

0 reviews
Rosahl M-3M1R membrane cover with minimal space requirements inside for drybox or Bambu Lab AMS / multi material systems
6
49
0
274
updated July 14, 2025

Description

PDF

This is an updated version of the M-3M1R outside mounting cover. It simplifies overall assembly, especially the USB-C power supply module can be assembled in advance (or ordered fully assembled!), snap-fits into its compartment and no need to fiddle wires through a tube in the part anymore. A protective grille structure with more narrow spacing has been added to all parts, which provides better protection of the membrane surface from either sides.

Operation Principle

Rosahl dehumidifiers are based on a solid-state polymer membrane. When supplied with a 3V DC voltage, moisture on one side is being decomposed into Hydrogen ions and Oxygen, the Hydrogen ions pass the membrane and recombine with air Oxygen to moisture again on the other side and get discharged. The Rosahl dehumidifiers are compact, work fully mainenance-free and the power consumption is very low.

The Rosahl M-3M1R membrane is suitable for storing multiple filament spools in a storage box of around 50-80l or Bambu Lab AMS or other multi material systems. With pre-dried filament spools (especially spools made of cardboard contain quite high moisture) a continous storage at approx. 15% rH and less is achievable. See diagram in pictures.

Bambu Lab AMS

I found that the Bambu Lab AMS is not as well sealed as the manufacturer states. Compared to a 50l storage box with gasket, where I achieved 5% of end humidity inside, the AMS can get down to like 16%, which is still considered a proper humidity level, see picture.

The Bambu Lab AMS sitting on top of the P1P/P1S/X1C printer gets passively heated a bit during print operation and hence further reduces relative humidity inside the AMS and makes the M-3M1R even more efficient!

Printing

The mounting cover is made of three parts, see pictures. All can be printed without any supports needed. The inner fixture requires a bit of bridging, so please check in the slicer if it did chose the proper bridging direction.

I printed with Overture PLA Professional on a Bambu Lab P1S. A .3mf file is available along with the STL models.

Assembly/Mounting

The inner fixture can be held upside-down to desired mounting position for marking the mounting holes. I found it works best to drill a first hole and then insert a screw into that hole to fix the position and then use the cover to drill the subsequent holes. I used a 3mm drill since the fixture has slightly larger holes and will hence comcompensate a bit of tolerance while drilling the holes.

Next the larger hole for the membrane has to be marked and cut out with e.g., a Dremel with a cutting disk.

When mounting to the Bambu Lab AMS it's preferable to drill a row of 3mm holes around the mebrane area and go with a small round file from hole to hole and finish with a flat file. See pictures of the M-1J1R outside cover for processing steps.

The inner fixture has two compartments, one for the M-3M1R membrane and one for the USB-C power supply module. The cables from the power supply to the membrane are routed through a hidden tube within the part. Feed the cables through that tube and solder the USB-C power supply on one end and 90° flat-connectors to the other end. Those are more convenient to solder than soldering directly to the membrane terminals. See below part list.

The USB-C power supply slides into a slot-like compartment, see pictures.

Before inserting the M-3M1R membrane make sure to insert a rubber sealing ring below the membrane into the recess.

When the membrane and the USB power supply module are inserted, the outer cover can be slid over the inner fixture. It holds the membrane in place.

Now the full part can be mounted to the enclosure with the original M-3M1R gasket going in between the part and the wall.

If the box wall is too soft and bends a bit away from the gasket you can add the back plate to the inside, which ensure proper sealing. This is not required for the Bambu Lab AMS, but it doesn't hurt adding it.

Parts Needed

The Rosahl M-3M1R dehumidifier membrane is available here, same for the USB-C power supply module here, which is now available fully assembled with cables and crimped flat connectors.

A kit with the M-3M1R membrane, USB-C module and above parts (except the storage box) is available here.

Gasket Damaged?

See here for 3d-printable spare gaskets in case of any issues with the original gasket during mounting.

Oxygen Increase Inside and Fire Hazard…?

Air density at sea level and 20°C is 1.204kg/m^3. Percentage of Oxygen is 20.94% so we have 252.1g Oxygen in 1m^3 of air. A relative humidity of 60%RH at 20°C corresponds to an absolute humidity of 10.37g/m^3. When we reduced this down to 10%RH, which corresponds to 1.73g/m^3, we have split 8.64g of H2O into Hydrogen and Oxygen and transported the Hydrogen to the outside. H2O is composed of 2x Hydrogen with a molecular mass of 1g/mol and 1x Oxygen with 16g/mol, so the Oxygen share of the above 8.64g H2O is 7.68g. So, we have increased the overall Oxygen in 1m^3 from 252.1g to 259.8g and hence increased the percentage from 20.94% to 21.6%.

Given this minimal increase, there is no need to worry about any negative impact of Oxygen concentration inside a Rosahl membrane based storage box.

Comments

Yeah, the Rosahl membranes are not cheap but they are crazy efficient when it comes to power consumption with less than 2W continously. I leave them running 24/7 without the need for ever re-drying a spool in a conventional filament drying or oven which would require significantly more power.

Tags

dryboxfilamentdryboxdehumidifierbambulabams

Model origin

The author marked this model as their own original creation.

License