English below.
Eigentlich wollte ich nur die losen Batterien in der Schublade etwas ordnen und dafür einen Behälter erstellen, in den alle hineinpassen. Doch dann hat mich die Idee und das Design so begeistert, dass es schließlich mehrere Varianten wurden.
Ganz nach dem Motto „So viel wie nötig - so wenig wie möglich“ entstand dieses Design mit den folgenden Vorteilen:
Weitere Varianten für 2, 3 und 4 Batterien befinden sich hier:
https://www.printables.com/model/1157947-battery-storage-r3aaa-curvyline
Da die Wandstärken dieses Modells sehr dünn sind, wollte ich eine Kombination aus Stabilität und Flexibilität erreichen, damit es auch einen Sturz übersteht. Aus diesem Grund habe ich das Modell mit PETG gedruckt.
Andere Materialien sollten in Bezug auf die Druckbarkeit auch problemlos funktionieren.
Das Modell ist für eine Druck-Schichthöhe von 0,25 mm und eine Extrusionsbreite von 0,45 mm optimiert. Damit die beiden Teile gut zusammenpassen und der Deckel weder zu locker noch zu fest sitzt, sollten diese Einstellungen beim Druck verwendet werden (alle Schichten und Perimeter).
Die besten Ergebnisse wurden mit der Einstellung „Arachne“ statt „Klassisch“ erzielt.
Zusätzlich sollte manuell eine „Aufmalnaht“ an einer Position gesetzt werden, an der die Batterie keinen Kontakt hat. Achte darauf, die Naht des Deckels mit der Naht des Unterteils abzustimmen (siehe Slicer-Screenshot).
Das Modell kann ohne Infill sowie ohne massive Boden- und Deckenschichten gedruckt werden, wenn:
Da das Unterteil „Down“ nur wenig Kontakt mit dem Druckbett hat, sollte bei unzureichender Haftung entweder die Druckbett-Temperatur erhöht oder ein Rand (Brim) verwendet werden.
Falls der Deckel oder die Batterien zu fest oder zu locker sitzen, kann dies über den Flow gut angepasst werden.
Das Modell lässt sich aufgrund der Form theoretisch recht schnell drucken. Bei Materialien wie PETG kann jedoch die Druckzeit pro Schicht zu kurz sein, um eine ausreichende Abkühlung zu gewährleisten.
In diesem Fall empfiehlt es sich:
Meine vollständigen Druckeinstellungen für einen PrusaMini+BondtechUpgrade sind den jeweiligen .3mf-Dateien zu entnehmen.
Für kreative Weiterverarbeitung ist die Blender-Datei beigefügt.
Happy Printing!
#############################################
English:
Actually, I just wanted to organize the loose batteries in my drawer and create a container that fits them all. But then I got so excited about the idea and the design that it ended up with several variations.
Following the motto "As much as necessary - as little as possible," this design offers the following advantages:
Additional variations for 5, 8, 13, and 18 batteries can be found here:
https://www.printables.com/model/1157947-battery-storage-r3aaa-curvyline
Since the walls of this model are very thin, I wanted to achieve a combination of stability and flexibility so that it could survive a drop. For this reason, I printed the model with PETG.
Other materials should also work fine in terms of printability.
The model is optimized for a layer height of 0.25 mm and an extrusion width of 0.45 mm. To ensure that the two parts fit together well and that the lid is neither too loose nor too tight, these settings should be used for all layers and perimeters.
The best results were achieved with the "Arachne" setting instead of "Classic."
Additionally, a manual "seam position" should be placed at a spot where the battery does not make contact. Make sure to align the seam of the lid with the seam of the base (see slicer screenshot).
The model can be printed without infill and without solid top or bottom layers if:
Since the base "Down" has very little contact with the print bed, it is recommended to either increase the print bed temperature or use a brim if adhesion is insufficient.
If the lid or the batteries fit too tightly or too loosely, this can be easily adjusted via the flow rate.
The model can theoretically be printed quite quickly due to its shape. However, with materials like PETG, the layer time might be too short for proper cooling.
In such cases, consider the following:
My full printing settings for a PrusaMini+BondtechUpgrade can be found in the respective .3mf files.
For creative modifications, the Blender file is also included.
Happy Printing!
The author marked this model as their own original creation.