Gamepad Quad Stand (Xbox360 and Custom) + Battery storage integrated

stores up to 4 gamepads practical and stylish + storage for baterys
6
14
0
120
updated December 28, 2024

Description

PDF

Ger:

Ständer zur Platzsparenden Aufbewahrung und zur schau Stellung von Gamepads.

In diesem Fall XBOX-360 Controller.

(Modell ohne Controller Aufnahme, für eigen Kreationen bzw. andere Gamepad Modelle als Download verfügbar)

 

Das Logo in der Mitte wird von Hand eingepresst und könnte ebenfalls durch ein eigens ersetzt werden.

 

Varianten:

Vollkörper = Druckbett min. 250mm

4Teilig = Per Dreh-Klick Verbund ohne Kleber (Montage siehe Hinweise unten)

Single Version = Eckversion für einen einzelnen Controller.

Blank = Eigene Kreationen bzw. Controller anderer Hersteller

Logo = xbox

 

4Teilig Montage:

Die Einzelteile sind Beschriftet 1-2-3-4 sowie mittig kleine Kennzeichnungen in form von Strichen, zur ersichtlichen Zusammengehörigkeit beim verdrehen.

Zu nächst 1+2 und 3+4 montieren.

Anschließen kann 12 und 34 kombiniert werden.

 

Zur Montage unter leichtem Druck die Teile ineinander drehen, kein Kleber notwendig.

ggf. die Kanten vorher entgraten!

Druckeinstellungen:

Aufgrund des Geschwungenen Designs empfehle ich eine Maximale Schicht höhe von 0,12mm besser wäre 0,08mm damit die Radien und Kurven edler aussehen. (am besten die Vergleichs Bilder anschauen)

Ich möchte noch dankend Matt Longieliere | Printables.com erwähnen.
Sein Modell eines Ständers war der Auslöser für meinen eigenen.
Er konnte mir bei der Erstellung hilfreiche Tipps geben :D

 

[ Gerne bei Fragen, Interesse oder kleinen Änderungswünschen kontaktieren ebenfalls wenn ihr mich Unterstützen wollt :D https://www.paypal.com/paypalme/clwmarcy ]

 

Eng:

Stand for space-saving storage and display of gamepads.

In this case XBOX-360 controller.

(Model without controller holder, available as a download for your own creations or other gamepad models)

 

The logo in the middle is pressed in by hand and could also be replaced by a custom one.

 

Variants:

Full body = print bed min. 250mm

4-part = twist-click connection without glue (assembly see notes below)

Single version = corner version for a single controller.

Blank = Your own creations or controllers from other manufacturers

Logo = xbox

 

4-part Assembly:

The individual parts are labeled 1-2-3-4 and there are small markings in the middle in the form of lines to make it clear that they belong together when twisting.

First assemble 1+2 and 3+4.

Then 12 and 34 can be combined.

To assemble, twist the parts together using light pressure, no glue required.

if necessary, deburr the edges before use!

 

Printsettings:

Due to the curved design, I recommend a maximum layer height of 0.12mm, 0.08mm would be better so that the radii and curves look more elegant. (Just look at the comparison pictures)

 

I would also like to thank Matt Longieliere | Printables.com
His model of a stand was the trigger for my own.
He was able to give me helpful tips when creating it:

 

[ Please feel free to contact me if you have any questions, interest or small change requests, also if you want to support me :D https://www.paypal.com/paypalme/clwmarcy ]

Tags



Model origin

The author marked this model as their own original creation.

License