Big Einsy Case - Plug & Play

This remix of this nice Big Einsy Case is optimized with Plug & Play for Maintenance. My idea was to get the printer quick out of my enclosure, which was a little hassle until these successful upgrade, because the Power Supplier and LCD are removed from the printer and they are outside of the enclosure. 

Shopping List

• 2x D-SUB Plug female, 15-pole, for IDC-Ribbon cable (Link, Reichelt) for LCD (P1 & P2) at Einsy side
• 2x D-SUB Plug male, 15-pole, for IDC-Ribbon cable (Link, Reichelt) for LCD (P1 & P2)
• 1x Ribbon cable, 10-pole (Link, Amazon) (optional) 
• 2x IDC-Connector, 10-pole (Link, Amazon) (optional)
• 2x RC-Power Plug, XT60E-M (Link, Amazon) for Power Supply at Einsy side
• 2x RC-Power Plug, XT60E-H (Link, Amazon) for Power Supply
• 1x M16 Connector, (Link, Amazon) for MMU
• 1x Wire like this one or you can cut the original power supply wires
• 4x Cable lugs like the red open ones if you want to make new cable and not use the original power supply wire.
• Heat shrink tubing (optional) 
• 8x Screw M2x 8 mm, socket head cap
• 4x Nut M2
• 1x 40x40 fan for the cover (optional, see original creator)
• 1x Soldering Skills (not optional for this setup)
• 1x Multimeter for checking the soldered cable.

Print

• 1x Big Einsy Case - Plug & Play
• 1x Cover from original creator.
• 1x all other small parts from original creator.

Assembly

Cable

• ATTENTION!!!
  •  !!! if you have an external LCD or want to install it outside, make sure the Ribbon is shorten then 0,5 m. From my experience I can tell, that if the cable is longer then 0,5 m the LCD will not work, because of the SPI-Communication Protocol. The SPI required short ways and fast feedbacks, because it is created for communication on PCBs. !!! 
  • !!! Make sure the device is unplugged when doing this work!!!
  • !!! Make sure when you cut the cable and or building new cable that you have an eye on the connection directions of the connectors !!!
• P1 Cable inside case
  • length of Ribbon Cable about 13-15 cm,
  • Power Panic cable, cut it to about 10 cm from Einsy Connection side
  • right side, IDC connector, 10-pole
  • left side, D-Sub connector, 15-pole
    • connect the Ribbon Cable to the right side and the Power Panic Cable to the left of the connector. (I first connected the Ribbon Cable and closed the connector to fix the Ribbon Cable. After this I reopened the connector again and inserted the Power Panic Cable)

• P2 Cable inside case
  • length of Ribbon Cable about 13-15 cm
  • right side, IDC connector, 10-pole
  • left side, D-Sub connector, 15-pole
    • connect the Ribbon Cable to the right side

• Power Supply Cable inside case
  • Lenghts of power supply cable 6-8 cm, 2x
  • solder the wire on the RC-Power Plug and cover it with heat shrink tube.
  • if needed press the cable lugs on the cable. 

• MMU Cable (I'm sorry, I forgot a to make a good picture of both ends)
  • Hold the Einsy Case in place on the printer and mark the length of the MMU Cable where the cable reach the opening on the top. Make sure that the cables are not stretched but loosely reach the case.
  • Solder each cable on the male and female connector. Make sure after you finished soldering the first connector that all connections are working. 
  • Solder the second connector and make sure the right cable are meeting.
  • My soldering overview. I also covered the cable with on heat shrink tube.

• Cable from Power Supply and LCD
  • basically repeat the first cable steps to build the other side of the connection and make sure that you use the counterpart of the connector and connecting the cables the right way. 

Case Assembly and Wiring

• Install the case on the Printer
• Install the Einsy into the case
• Start wiring according Prusa manual. 
• Here my wiring result.

If anything unclear, need to described more clear or is not understandable due to bad English, please ask in the comments for help. I will try my best. Have fun with this mod.