K1C nozzle wiper with A1 mini brushes

Disclaimer:

My A1 Mini nozzle wiper is missing “teeth” because an earlier design didn't hold the probed pads on good enough.

You will need to have your printer rooted to be sure it will not interfere with the probed area.

Needed materials:

Print the part out of a higher temp material, PETG, ABS, etc.

Buy A1 Mini nozzle wipers

An old nozzle wiper from a K1C build plate

Instructions

Cut the original K1C nozzle wiper pads off at each end, cut more than you think you may need, cut until they are a press fit into each inset square, this is to ensure they don't get knocked out over time.

Cut one of two of the A1 Mini nozzle wipers until it is a press fit, if it is to loose they will come out over time.

Remove the two screws at the rear lead screw, start the screws in your new part then reinstall.

Then update the software!

Update software:

If you haven't rooted your printer yet here is a guide: https://guilouz.github.io/Creality-Helper-Script-Wiki/firmwares/install-and-update-rooted-firmware-k1/

Navigate to your printer.cfg file and change bed_mesh.

[bed_mesh]
speed: 150 
mesh_min: 5,5
mesh_max: 215,212  #This is the thing that you need to change so the nozzle doesn't hit the edge of the nozzle wiper.
probe_count: 6,6
fade_start: 5.0
fade_end: 50.0

Cyclops extruder

If you have a cyclops extruder on a K1C the software change will be different along with the wiper itself.

I only changed two lines in this but it'll probably be easier to just copy the entire things

[prtouch_v2]
pr_version: 1
step_base: 2
z_offset: 0 
noz_ex_com: 0.06
tilt_corr_dis: 0
tri_min_hold: 2500
tri_max_hold: 6000
pres_cnt: 4
pres0_clk_pins: leveling_mcu:PA5
pres0_sdo_pins: leveling_mcu:PA1
pres1_clk_pins: leveling_mcu:PA2
pres1_sdo_pins: leveling_mcu:PA0
pres2_clk_pins: leveling_mcu:PA6
pres2_sdo_pins: leveling_mcu:PA3
pres3_clk_pins: leveling_mcu:PA7
pres3_sdo_pins: leveling_mcu:PA4
show_msg: False
step_swap_pin: PC10
pres_swap_pin: leveling_mcu:PB1
g28_wait_cool_down: true
pa_clr_down_mm: -0.15
clr_noz_start_x: 87            #I changed this line
clr_noz_start_y: 217          #and this line
clr_noz_len_x: 46
clr_noz_len_y: 1
speeds: 2.5,1.0
tri_hftr_cut: 2,1
tri_lftr_k1: 0.70,0.30
tri_try_max_times: 10
tri_min_hold: 2500,20000
tri_max_hold: 6000,60000

clr_noz_quick: true
clr_quick_high:0.7
clr_xy_quick_spd:100
clr_quick_times:10
clr_quick_react_dis:5

Make sure your y max value is also changed, mine was

[stepper_y]
step_pin: PB8
dir_pin: !PB7
enable_pin: !PC3
microsteps: 32
rotation_distance: 40
endstop_pin: tmc2209_stepper_y:virtual_endstop
position_endstop: -0.5
position_min: -0.5
position_max: 218            # I changed this line
homing_speed: 30
homing_retract_dist:0

Different capability.