Get Free Shipping & Prusaments with the Prusa XL Summer Deal!
ntalekt 18
ntalekt
@ntalekt_371042
published a new model October 3, 2024 at 6:29 PM
October 3, 2024 at 6:29 PM

Ctrl + Enter to send Enter to add a new line
ntalekt 18
ntalekt
@ntalekt_371042
published a new model November 29, 2023 at 12:49 AM
November 29, 2023 at 12:49 AM

works as intended :)

thanks

Very nice project! Printed with PLA.

Ctrl + Enter to send Enter to add a new line
ntalekt 18
ntalekt
@ntalekt_371042
published a new model November 29, 2023 at 12:45 AM
November 29, 2023 at 12:45 AM

Works perfectly, makes my life easier.

Ctrl + Enter to send Enter to add a new line
ntalekt 18
ntalekt
@ntalekt_371042
published a new model September 26, 2023 at 2:37 PM
September 26, 2023 at 2:37 PM

Printed in Matt grey PLA from bamboo labs. Works great, but a little difficult to get some of the pills out

Ctrl + Enter to send Enter to add a new line
ntalekt 18
ntalekt
@ntalekt_371042
published a new model September 21, 2023 at 4:00 AM
September 21, 2023 at 4:00 AM

Works great! Any chance you can upload a set with a single stud in the middle for minifigs with a 2x2 base (like robes or dresses)? (edited)

Ctrl + Enter to send Enter to add a new line
ntalekt 18
ntalekt
@ntalekt_371042
published a new model August 7, 2023 at 5:26 AM
August 7, 2023 at 5:26 AM

Ctrl + Enter to send Enter to add a new line
ntalekt 18
ntalekt
@ntalekt_371042
published a new model July 28, 2023 at 12:49 PM
July 28, 2023 at 12:49 PM

Printed in Addnorth PETG. Great, clean model. Prints well and is very sturdy and stable. 6/5 stars.

It come ot nice and fast 3h30min. But it look a litle bit reduced /shrinked. Maybe cous of printer bed 220x220mm ankermake m5c

Ctrl + Enter to send Enter to add a new line
ntalekt 18
ntalekt
@ntalekt_371042
published a new model July 26, 2023 at 10:14 PM
July 26, 2023 at 10:14 PM

Printed for Anycubic's cruise ship contest.

Ctrl + Enter to send Enter to add a new line
ntalekt 18
ntalekt
@ntalekt_371042
published a new model July 26, 2023 at 1:02 AM
July 26, 2023 at 1:02 AM

What plate type do you select in Bambu studio when using the PEO plate? Also, does the plate require any adhesive?

Ctrl + Enter to send Enter to add a new line
ntalekt 18
ntalekt
@ntalekt_371042
published a new model July 10, 2023 at 1:30 AM
July 10, 2023 at 1:30 AM

Great model, fists well, printed in PLA Galaxy Black. Thanks for sharing!

Printed the wall mounts with Bambu black Filament. Very nice and handy stls and the result looks awesome!

Ctrl + Enter to send Enter to add a new line
ntalekt 18
ntalekt
@ntalekt_371042
published a new model June 23, 2023 at 3:34 PM
June 23, 2023 at 3:34 PM

ntalekt 18
ntalekt
@ntalekt_371042
published a new model June 22, 2023 at 3:31 AM
June 22, 2023 at 3:31 AM

I understand this is not waterproof. Where is it supposed to be mounted in case of a pool? (edited)

@John_166367 I'm planning on using double-sided tape to attach it to the back of the solar panel. The DS18B20 sensors I purchased have a 3 meter cable so the probes just need to reach the pool/spa. The protection provided by the solar panel should be enough for my use case.

You could also mount the sensor box somewhere safer and waterproof. Then run the power from the solar panel to it. The world is your oyster. I live in the desert so the sun will destroy it before any water ingress.

Happy printing!

wow very cool project.
Including all the links is especially cool of you thanks.

Ctrl + Enter to send Enter to add a new line
ntalekt 18
ntalekt
@ntalekt_371042
published a new model June 14, 2023 at 5:36 AM
June 14, 2023 at 5:36 AM

Ctrl + Enter to send Enter to add a new line
ntalekt 18
ntalekt
@ntalekt_371042
published a new model June 3, 2023 at 1:14 PM
June 3, 2023 at 1:14 PM

Printed in black PLA and it fits perfectly with umbrella and holder.

I trimmed the bottom section off in Prusa as I didn't need it that deep but it was a perfect fit.

Ctrl + Enter to send Enter to add a new line
ntalekt 18
ntalekt
@ntalekt_371042
published a new model September 18, 2022 at 6:15 PM
September 18, 2022 at 6:15 PM

Ctrl + Enter to send Enter to add a new line
All items loaded