andrew gipson 23
andrew gipson
@agipson
published a new model November 28, 2024 at 8:24 PM
November 28, 2024 at 8:24 PM

Very creative design, and a fun build. The only trouble I experienced were the forearm armor parts not sticking to the build plate, no matter where I had them. I also had to tap the biceps in with a hammer, as they were super tight. Overall a great set of armor to use on the Dummy system.

@SyvariZero Thanks for the heads up! I'll be uploading an updated bicep armor piece with .025 additional clearance on all the inner faces. Print looks great btw πŸ‘Œ

The joints on the middle bit of the legs kept falling off when I was trying to pose him, I ended up using the original Dummy joints and it worked a lot better. I like the design of the feet, they're pretty close to my original design for my Spider Walker legs before I decided to just go full insect with 'em.

Ctrl⌘ + Enter to send Enter to add a new line
andrew gipson 23
andrew gipson
@agipson
published a new model November 24, 2024 at 7:23 PM
November 24, 2024 at 7:23 PM

I was looking for something like this and you delivered! Its not hard to print at all as you can put the handles on their flat side. The handles fit perfectly in the dummy 13 hands and don’t get stuck or have a problem unless its with the hand itself. The only problem I had is that I had to cut a bit off the base of the straight blades for them to fit and I secured most of the parts with super glue. Although, I did have to hit the handles in. Otherwise, it really is a great weapon for the 13.

Ctrl⌘ + Enter to send Enter to add a new line
andrew gipson 23
andrew gipson
@agipson
published a new model November 23, 2024 at 10:35 PM
November 23, 2024 at 10:35 PM

Is this model compatible with the sword/ gun hands? If so what frame piece should I use?

@Tom2i3u3o_2628417 i will update the sword/gun hand page today with the frame bit for this model

edit: it's up on the other page (edited)

I noticed the swords that they hold are similar to the ornate scythes/spears. Will that be the newest model?

Ctrl⌘ + Enter to send Enter to add a new line
andrew gipson 23
andrew gipson
@agipson
published a new model November 2, 2024 at 6:12 PM
November 2, 2024 at 6:12 PM

Hi, the prongs don't seem to fit into the slots on any of the pieces? Are they meant to be at different scales or am I just not trying to insert the right pieces into each other?

View 2 more comments

@LiamEgbert_2475922 I would try reprinting the forearm with prong frame bit with a -.1mm xy compensation (I forget what the slicer calls it but it's the setting you use to make the models dimensions either bigger or smaller basically)

@LiamEgbert_2475922 or just like kinda cut the corners off of the prong

Ctrl⌘ + Enter to send Enter to add a new line
andrew gipson 23
andrew gipson
@agipson
published a new model October 20, 2024 at 12:35 AM
October 20, 2024 at 12:35 AM

andrew gipson 23
andrew gipson
@agipson
published a new model October 18, 2024 at 5:15 AM
October 18, 2024 at 5:15 AM

This is by far my favorite style backpack arms mod for these figures! Well done!!

Ctrl⌘ + Enter to send Enter to add a new line
andrew gipson 23
andrew gipson
@agipson
published a new model October 15, 2024 at 9:28 PM
October 15, 2024 at 9:28 PM

LAGOTHRIX 13 is an excellent take on the 13-series frame. This design exhibits appealing mechanical textures, and the collar lends the finished figure a decidedly tactical attitude that demands an arsenal to match. In addition, the default print orientations and lack of long bridges make this figure much simpler to print and assemble compared to the original Dummy 13.

Printed in PETG for both frame and armor, at a layer height of 0.2mm. I opted for a combination of the heavy alternate shoulder and upper arm armor, while retaining the slimmer default armor on the lower arm. (edited)

Ctrl⌘ + Enter to send Enter to add a new line
andrew gipson 23
andrew gipson
@agipson
published a new model October 12, 2024 at 7:28 PM
October 12, 2024 at 7:28 PM

Ctrl⌘ + Enter to send Enter to add a new line
andrew gipson 23
andrew gipson
@agipson
published a new model October 9, 2024 at 3:10 AM
October 9, 2024 at 3:10 AM

Love the look of the Owl Armor! Matches great with these mechanical wings I found!

View one more comment

@SandyWaffler_2565487 here is the link! DO NOT print these in PLA. A few of the parts will break easily so be very careful when putting them together.
β€Šhttps://makerworld.com/en/models/682830#profileId-611418

Ctrl⌘ + Enter to send Enter to add a new line
andrew gipson 23
andrew gipson
@agipson
published a new model September 26, 2024 at 10:28 PM
September 26, 2024 at 10:28 PM

printed amazingly, all i had to do was rotate the blade on its side, printed without supports easily.

I love this model it's awesome. It's cool to toy with and it reminds me of the Grim reaper but in a futuristic timeline.

Ctrl⌘ + Enter to send Enter to add a new line
andrew gipson 23
andrew gipson
@agipson
published a new model September 26, 2024 at 3:35 AM
September 26, 2024 at 3:35 AM

Just finished making this guy yesterday! Printed entirely out of PLA on my Voron 0.2. Super happy with how it turned out. Next one will be the Sentinel 13! (edited)

View one more comment
Ctrl⌘ + Enter to send Enter to add a new line
andrew gipson 23
andrew gipson
@agipson
published a new model September 24, 2024 at 4:17 PM
September 24, 2024 at 4:17 PM

Ctrl⌘ + Enter to send Enter to add a new line
andrew gipson 23
andrew gipson
@agipson
published a new model September 9, 2024 at 11:32 PM
September 9, 2024 at 11:32 PM

Ctrl⌘ + Enter to send Enter to add a new line
andrew gipson 23
andrew gipson
@agipson
published a new model August 31, 2024 at 1:30 AM
August 31, 2024 at 1:30 AM

Ctrl⌘ + Enter to send Enter to add a new line
andrew gipson 23
andrew gipson
@agipson
published a new model May 19, 2024 at 5:49 AM
May 19, 2024 at 5:49 AM

Very nice πŸ™‚
My son loves it!

Ctrl⌘ + Enter to send Enter to add a new line
andrew gipson 23
andrew gipson
@agipson
published a new model May 5, 2024 at 7:06 PM
May 5, 2024 at 7:06 PM
NSFW

Great model, I had only one problem - the support under her kitty haha

Print came out great. Just ordered some marble filament for a more realistic result.

Ctrl⌘ + Enter to send Enter to add a new line
andrew gipson 23
andrew gipson
@agipson
published a new model April 26, 2024 at 1:32 AM
April 26, 2024 at 1:32 AM

Ctrl⌘ + Enter to send Enter to add a new line
andrew gipson 23
andrew gipson
@agipson
published a new model March 21, 2024 at 10:32 PM
March 21, 2024 at 10:32 PM

A really fun build. Having the cannon and armor bottom separate make for a very dynamic weapon. The print went really easily. Great design. I am ready to get the BIG guns printed next.

@LoganWan_1927327 I recommend low infill% or lightning infill for the larger weapons. Great looking print!

Ctrl⌘ + Enter to send Enter to add a new line
andrew gipson 23
andrew gipson
@agipson
published a new model March 21, 2024 at 1:15 AM
March 21, 2024 at 1:15 AM

Could you make this in STL format? Please and thank you

Ctrl⌘ + Enter to send Enter to add a new line
andrew gipson 23
andrew gipson
@agipson
published a new model March 19, 2024 at 6:34 PM
March 19, 2024 at 6:34 PM

Ctrl⌘ + Enter to send Enter to add a new line