TommyUnreal 16
TommyUnreal
@TomasSmolik_1005307
published a new model September 8, 2024 at 11:17 AM
September 8, 2024 at 11:17 AM

Ctrl + Enter to send Enter to add a new line
TommyUnreal 16
TommyUnreal
@TomasSmolik_1005307
published a new model June 3, 2024 at 9:13 PM
June 3, 2024 at 9:13 PM

Thank you. i printed the 1mm discs and they work fine.

Ctrl + Enter to send Enter to add a new line
TommyUnreal 16
TommyUnreal
@TomasSmolik_1005307
published a new model February 19, 2024 at 10:24 PM
February 19, 2024 at 10:24 PM

Prototype printed in PLA (Body) and PETG (Axle, Wheels). Works fine, but the rubber band I found gives it a big boost at the start, but doesn't deliver it over a long time.

@TomasSmolik_1005307 This is due to the principle because no tension can be applied to the rubber band that is already wound up. Thus, only the remaining portion of the rubber band is stretched, resulting in very little energy being stored, and the force quickly diminishing.

@uhltimate_548874 You are absolutely correct! What I meant is that different bands will perform differently, based on length and flexibility.

I couldn't quite figure out how to work it but it's a pretty cool model none the less I printed in some pla and it looks pretty good.

Ctrl + Enter to send Enter to add a new line
TommyUnreal 16
TommyUnreal
@TomasSmolik_1005307
published a new model January 15, 2024 at 9:28 PM
January 15, 2024 at 9:28 PM

40 pcs that fit my drawer almost perfectly. I used 1.3 kg of PETG filament, but when all the holders are connected, it is sturdy enough to lift all 40 holders with spice jars in place.

Really good design, wish my drawers is deep enough to print this.

Ctrl + Enter to send Enter to add a new line
TommyUnreal 16
TommyUnreal
@TomasSmolik_1005307
published a new model January 6, 2024 at 11:52 PM
January 6, 2024 at 11:52 PM

I really enjoy this design, it completely fits my interior! I printed it flat on its side.

My hooks have to hang with double sided tape (not allowed to drill), which was a little bit hard because the small surface of the tail. If you need to use tape as well, I'd definitely widen the model.

Thanks for a lovely design!

@TeDee looking great! Thank you for posting this. I'm glad you like the design.

Ctrl + Enter to send Enter to add a new line
TommyUnreal 16
TommyUnreal
@TomasSmolik_1005307
published a new model January 3, 2024 at 4:28 PM
January 3, 2024 at 4:28 PM

Ctrl + Enter to send Enter to add a new line
TommyUnreal 16
TommyUnreal
@TomasSmolik_1005307
published a new model January 2, 2024 at 8:28 PM
January 2, 2024 at 8:28 PM

Printed in Black GEETECH PETG.
Bed: 70°C
Nozzle: 240°C
Layer Height: 0.16 mm

Ctrl + Enter to send Enter to add a new line
TommyUnreal 16
TommyUnreal
@TomasSmolik_1005307
published a new model January 1, 2024 at 4:54 PM
January 1, 2024 at 4:54 PM

Printed in Black GEETECH PETG.
Bed: 70°C
Nozzle: 235°C
Layer Height: 0.28mm

Ctrl + Enter to send Enter to add a new line
TommyUnreal 16
TommyUnreal
@TomasSmolik_1005307
published a new model January 1, 2024 at 2:28 PM
January 1, 2024 at 2:28 PM

Gembird PLA Yellow
Spectrum Premium PLA Navy Blue

Nozzle: 205°C
Bed: 60°C
Layer Height: 0.20mm

Ctrl + Enter to send Enter to add a new line
All items loaded