Jamie 18
Jamie
@Jamie
published a new model October 11 at 9:29 PM
October 11 at 9:29 PM

Ctrl + Enter to send Enter to add a new line
Jamie 18
Jamie
@Jamie
published a new model May 28, 2023 at 6:10 PM
May 28, 2023 at 6:10 PM

Awesome! Can't wait to try the drag knife! (edited)

Using 32mm magnet, and epoxied 1.25" washers into the other side. (edited)

@SupraGuy In my case I only used one washer, in which case it's recessed below the lip by about 1.9 mm. (The magnet side is flush.) Multiple washers adding metal and bringing the surfaces closer will have a big impact on the pull strength!

Ctrl + Enter to send Enter to add a new line
Jamie 18
Jamie
@Jamie
published a new model May 10, 2023 at 2:31 AM
May 10, 2023 at 2:31 AM

Ctrl + Enter to send Enter to add a new line
Jamie 18
Jamie
@Jamie
published a new model May 7, 2023 at 8:03 PM
May 7, 2023 at 8:03 PM

Ctrl + Enter to send Enter to add a new line
Jamie 18
Jamie
@Jamie
published a new model December 11, 2022 at 9:11 PM
December 11, 2022 at 9:11 PM

Ctrl + Enter to send Enter to add a new line
Jamie 18
Jamie
@Jamie
published a new model November 21, 2022 at 7:06 AM
November 21, 2022 at 7:06 AM

Ctrl + Enter to send Enter to add a new line
Jamie 18
Jamie
@Jamie
published a new model September 25, 2022 at 11:05 PM
September 25, 2022 at 11:05 PM

Ctrl + Enter to send Enter to add a new line
Jamie 18
Jamie
@Jamie
published a new model August 28, 2022 at 6:10 AM
August 28, 2022 at 6:10 AM

- Inland White PLA+
- Sliced in Cura 5.2.1
- 15% Infill
- Nozzle Temp: 220°C
- Build Plate Temp: 70°C
- Print Speed: 60 mm/s

When I load this in openscad It shows the trays as blocks. and I get an error that says: can't open include file modules/gridfinity+modules.scad. Any ideas? (edited)

View one more comment

@Jamie Hi , it doesnt recognize the module even when download as zip. Any suggestion?

Ctrl + Enter to send Enter to add a new line
Jamie 18
Jamie
@Jamie
published a new model July 13, 2022 at 7:10 AM
July 13, 2022 at 7:10 AM

@Pilinguijo it is an old Vivitar tripod I've had for years. It's a temporary solution. I'll eventually build a sturdier motorized mount.

Great design, I love it! Great to see you provided the OpenSCAD source code, and thanks a lot for providing metric dimensions! Non-metric standards can be very confusing at times - here's a helpful site (which confirms your conversion is spot-on): https://www.schrauben-lexikon.de/td8-zoll-umrechnung.asp#820

Ctrl + Enter to send Enter to add a new line
Jamie 18
Jamie
@Jamie
published a new model July 9, 2022 at 8:29 PM
July 9, 2022 at 8:29 PM

Ctrl + Enter to send Enter to add a new line
Jamie 18
Jamie
@Jamie
published a new model June 11, 2022 at 4:50 PM
June 11, 2022 at 4:50 PM

Ctrl + Enter to send Enter to add a new line
All items loaded