used test sample for sizing. Printing off right now. Was hoping you would post these wide stance legs. Seen them in the video awhile back. Thanks for sharing the files! Will post a pic when finished

Great work! Thx for sharing... the feet are absolutly an improvement!

Hello I have Question Do this fits on a k1max ?
Thanks

Can you provide more information on this mod? Have you changed the control board? what length belts are you using?

hello, what is the best material to make these fasteners from.

https://www.amazon.com/POLISI3D-Upgrade-Coupling-Compatible-Printers/dp/B0C1NFZ3Y6 for those who are looking for the couplers, I found the same ones he used (I think, the product images are the same on the Amazon page. correct me if i'm wrong)

Can anyone at all clarify if these will fit on an ikea lack table still?

thank you for all your efforts would you put into designing these legs they are really wonderful and works perfectly printing was absolutely easy and I use a red petg. combining with the full door hinge. I see some improvements also in input shaper and over all stability

Like a charm...

Thanks DED this is hands down amazing, Creality take notes and do this from the factory. Note to anyone installing, I used the bed screws to hold the power supply loosely in place, rotated the mount for the rails and started top right 4x20 SHCS then rotated part into place and installed bottom left 20mm SHCS then mounted rest of hardware. (edited)

Beautiful fit in every regard: screw holes and countersinks, sliding parts, and snap-in retention.

My only issue is that my Creality sensor has a very large reinforced segment of the cable that I need to tie back to avoid having it hit the gantry during Y-axis homing.

Work good but the part on the sensor is hard to snap, I broke one wing, but it work at the end. I could be great to have also the 3 parts in a separated file if we need to only print again one the 3.

A few errors in the instructions: the screw needed for the tool head is 8mm not 6, because the tool head original screw are 6mm not 4mm.

I do not own on of these yet as I'm still deciding on if I should get another Creality or not. Would it be a bit better if the adjustment was adjustable? What I mean is that you could move the adjustment wheel in and out to add or reduce the tension instead of applying a single level of pressure on the belt? Just a thought. I know that I don't like the V3 KE's belt tensioning as well as no manual leveling at all for the bed. But I'm sure that the community will or already has figured out how to overcome these, as you are doing.
Addedum: LOL. I just looked at the remix. Already done. (edited)

Great work!

Need to know who as installed this on their KE ??? And how did you managed to install the Beacon Module in Klipper ??? Nebula pad cannot seem to be able to support this script as it is a Klipper clone and missing files or so ?!? tks

Still waiting for some parts to de-Nebula my KE, but really stoked to get this lil guy mounted. Thanks for the model Derrick! Haven't seen anyone post a make yet but mine turned out nice. Overture Clear PETG, 4 walls, 100% infill. It's no ABS but it'll do I think.

Hello, how do make the sensor working. My KE always says that no sensor is connected

@DerrickDarrell The two side pieces are to far from the ground. Could you divide them? I'm new and really don't now how to do that myself.

Hi! To install this upgrade on a K1C, is it necessary to change the motors and pulleys?
Congratulations on the mod!
Regards!

Works great!

what about the 360 door hinge?

does it really strength up the frame?

Did a quick test and the results speak for themselves. Highly suggest this mod if you print a lot of high temperature materials. I did buy the Berserker fans from west 3D they have almost double the CFM than the WINSINN fans shown in the picture.

Got the K1 Max up to 61c after a 30 minute heat soak with the fan add ons.

Before I was getting 42c to 47c chamber temps.

Definately a big help with higher temp materials that need a enclosure or heated Chamber.

Great Design. Will be adding to the rest of our K1 flight.

This is the final result. I cant thank you enough!

Thanks for sharing. I had your design printed in a textured PA12 by a MJF process. It came out nice and will look even better primed and painted.

Thanks Darrell, cant wait for the z mods I saw you showing off on the d3vil design discord

The only thing i added was the Creality logo. the supports inside were a little difficult to remove i probably could have messed with it in the slicer a little more but other than that it was an easy print Thanks

Wanted to give a little special taste to my k1m....looks great!

Added some color! Worked well. Printed mine in abs.

I managed to complete this install on my K1 Max. It took some extra work though. For starters, you have to sacrifice the lidar because the calibration plate will block where the 2nd fan needs to go, so it has to come off. I removed the plate and the lidar itself since the last couple times I tried to use it, it wouldn't work anyways. Next, you have to modify the hotbed wire support bracket. It's held in by three screws so you have to take it off, cut it down into a "L" shape like in my photos. Then you have to move it back one of the screw holes and put it back in so that it's held by 2 screws, instead of 3. After that, every else was exactly as described and I'm very happy with the end results. I actually prefer the better cooling over the lidar anyways. Thanks for the file and parts list, greatly appreciate it :)

Mind sharing the Stp file for it ?
I want to remodel it to fit my Rook printer, but mirroring it fro a stl with over 10K triangles is a hell of a job :)

Printed lid riser with modified inserts to add extra LED lighting.

Everytime is a sunny day now hahha

Works great, and seals the gap behind your control panel.

Doesn't work with K1 Max (the notch doesn't fit). Would be nice if you could add in the description that this is not for K1 Max.
Thanks!